change differential grease By kalee (Read 2,462 times)

[kalee]

I'm sure this is listed some where alley but have been unable to locate it. How does a person go about changing the differential grease ? mine is slinging grease on the underneath side of the rear fenders and on the frame and here in south Tx. were already getting into the 100's, it was 102 here yesterday.
Thanks
kalee

[dragonsparks]

I know it's not a trike 150 but should be the same.



dave

[kalee]

Thanks Dave,,,No it isnt the same, mine has like synthetic grease in the rear end or gun grease . Its slinging grease up under the rear fenders and on to the frame and its in the upper 100's here in south Tx.
kalee

[Alleyoop]

Dragon,
That is changing the TRANNY OIL.
Kalee is asking about the DIFFERENTIAL, anyway KALEE.

You do not change the GREASE in the DIFFERENTIAL you just add grease. Look on the DIFERENTIAL you should see a GREASE NIPPLE on it.

Also get DIFFERENTIAL GREASE that is RATED OVER 240 so it does not LIQUIDIFY with low temps that will help and stop some of the grease becomeing liquid and sipping out and flung out.

Here is the GREASE NIPPLE ON THE DIFFERENTIAL:
Alleyoop

Here is a very high Temp rated grease for very hot areas:

www.castrol.com/liveassets/bp_internet/castrol/castrol_usa/STAGING/local_assets/downloads/0-999/5417.PDF

[dragonsparks]

Thanks Alley. LOL. My bad Dragon. Kalee.




Dave

[kalee]

Yes I know where the nipple is, Thanks alleyoop thats what I needed to know. I will check with my local auto store and see if they carry this type of grease.
Thanks agin alleyoop
kalee

[kalee]

dragonsparks,,, Your a good dragon, some times I wish I was talented enough to put picture's on here, alley had to put the pictures of my trike on here I emailed them to alley and he put them on this forum for me,,, Practice, Pratice I guess
kalee

[kalee]

dragonsparks,, my ice bear trike 150cc is listed under bad vibration rattle.
kalee

[Alleyoop]

Try pushpictures it is the easiest:
Alleyoop
You can use push picture to put up pictures here it is easy and free:

picturepush.com/host.php?image=10075950

1. Click on the BLUE UPLOAD another image
2. Click on BROWSE
3. That will display your computer directories
4. click on where your picture is at
5. Click on your picture and click on OPEN and it will load it
6. Then scroll down to the box where it says640*480
7. Click on the 2nd entry in those links -- it will turn blue
8. Right click and click copy
9. Come here and right click and paste it in your post.

[kalee]

I'm not sure what I done wrong here alleyoop but I thought there would be a picture not a website
kalee

[Alleyoop]

There are TWO MOTOR MOUNTS at the rear they should be tight.

Then there is 1 LONG BOLT going through TWO FRAME BRACKETS
and the MOTOR MOUNTS ARE IN THE MIDDLE and the LONG BOLT goes through all FOUR and that ALSO SHOULD BE TIGHT.


After it loaded your picture You did the last part wrong:
Here is what you do AFTER it loads the pic. You will get it then you can put up all kinds of pic.
Alleyoop
After you click on copy you come here and PASTE it.

[kalee]

This is the bolt I was talking about that fastens the motor to the swing arm

[kalee]

Bygolly alley I think I got it this time, this bolt was there but it wasnt tight but it is now, I have checked everything in and around the rear end and found several bolts that was not snug. What I call snug is using the right sized metrc wrench and pulling them tight by hand as tight as I can get them.
kalee

[Alleyoop]

FANTASTIC!! Now you can put up pictures all day long(HAHA).

Yea none of the bolts back there should be loose also the motor mounts they all should be tight.
Good Job
Alleyoop

[kalee]

Thanks alleyoop for your guidance, I found a few bolts on my differential that needed to snugged a little tighter to.
kalee,,,,, Thanks again for the info.