|
|
Post by Alleyoop on Sept 13, 2013 18:51:09 GMT -6
Yes you could try that as well, get some DUCK TAPE and try it can't hurt it won't run with out doing something to cut off some air anyway(HAHA).
Alleyoop
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 13, 2013 19:57:55 GMT -6
i put some duck tape over the hole in the airbox and it did help it stay running a little better. I'll adjust the A/F screw tomorrow with the tape on and see what I can do.
|
|
|
|
Post by Alleyoop on Sept 13, 2013 20:00:58 GMT -6
There you go, you can always add or take away tape.
Good job
Alleyoop
|
|
|
|
Post by Alleyoop on Sept 14, 2013 18:54:39 GMT -6
So what is the VERDICT were you able to cut enough air to get it running half way descent or what.
Alleyoop
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 14, 2013 22:37:23 GMT -6
Ok, so i've made some progress, i hope. I readjusted the valves to .005 and it will now start without me putting my hand over the intake. It will almost immediately die after it starts. What would you suggest next, alley? Should i readjust one of the valves to compensate this? maybe lower one or raise one? Sorry if that's a silly question.
|
|
|
|
Post by Alleyoop on Sept 14, 2013 22:42:53 GMT -6
Turn the IDLE SCREW that is the one on the throttle side with the SPRING under it the one over the THROTTLE Control wheel that the throttle cable goes around and hooks up to. TURN that screw Clockwise about 1/8 of a turn to open the butterfly a little more.
Alleyoop
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 14, 2013 22:44:09 GMT -6
I'll go give it a shot right now.
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 14, 2013 22:49:19 GMT -6
Ok, so adjusting the idle screw makes little difference in how long it runs. It will start up, idle high and then die. i can keep it going a bit longer with some throttle but it still dies pretty quick.
|
|
|
|
Post by Alleyoop on Sept 14, 2013 22:53:25 GMT -6
tape up a little more on the air filter.
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 14, 2013 22:55:42 GMT -6
ok, I will do that tonight. I'll get back to you soon with it. I probably shouldn't try running it much more tonight. My neighbors might hate me by morning if i do lol
|
|
|
|
Post by Alleyoop on Sept 14, 2013 22:59:12 GMT -6
Ok, just try cutting off some more air and you can lower the idle a little turn that idle screw Half COUNTER CLOCKWISE back so when it starts it does not idle so high.
You will have to play with the taping of the Air Filter.
All you can do Unless you just order a new Air Box or put on a cone filter that you can then tape off by just wrapping tape starting from the end of it till you can get the mixture right.
Alleyoop
Alleyoop
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 14, 2013 23:03:10 GMT -6
Thanks! I'll def let you know what i get going. I really appreciate all the help.
|
|
Senior Clinician
Currently Offline
Posts: 219
Likes: 0
Joined: Sept 10, 2013 8:28:19 GMT -6
|
Post by sumdawgtwigg on Sept 15, 2013 12:26:39 GMT -6
She runs and rides! Alley, you were spot on! What I ended up doing was putting the foam back in the air box and then taped it. I slowly covered more foam with tape until she ran perfect! I'm going to order a new box tonight! Thanks so much! Going Riding now  |
|
..BAD TO THE BONE..
