|
|
Post by Alleyoop on May 10, 2011 19:13:51 GMT -6
Well I hope the Clang was just something in the CVT and not the Tranny Gears.
Does your Trike have a REVERSE?
So take the CVT cover off and HOPE its the Clutch. What kind of belts are you buying that they are MELTING?
Lefty
|
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on May 10, 2011 20:39:32 GMT -6
When it started did you rev it enough to engage the belt?/ Make sure the cvt rollers did not stick...
I could use another Magnum..
mike
|
|
|
|
Post by Alleyoop on May 10, 2011 21:40:54 GMT -6
HEHEHE!! Man your slick Mike, maybe this one for $200.00 since its a 150cc  Alleyoop |
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on May 11, 2011 4:39:26 GMT -6
|
|
Certified Clinician
Currently Offline
Icebear Trike 150-9
Posts: 56
Likes: 0
Joined: May 31, 2010 20:32:41 GMT -6
|
Post by Triker98304 on May 14, 2011 13:41:11 GMT -6
5/13/02011, I got the trike started and it would not move. engine fired right off and it ran. Took the variator and belt off. All that looks ok. Pulled the clutch off and found the clutch spring rusted to the clutch bell housing. While the trike was up on the jack I checked the tires and the pass side rear tire had side motion...NOT GOOD. Pulled the tire and found that a cotter key to hold the axle nut was missing...both sides. Does any one know the torque for the axle nuts? for now I tightened them with an impact wrench so there is no movement on the hub. Thought I'd change the fuel filter but I did not have the proper hose clamps. I will change the engine oil and tranny grease and hopefully get riding again...Tomorrow is another day Right!
Ya-all ride safe. Triker98304
|
|
Certified Clinician
Currently Offline
Icebear Trike 150-9
Posts: 56
Likes: 0
Joined: May 31, 2010 20:32:41 GMT -6
|
Post by Triker98304 on May 14, 2011 13:48:56 GMT -6
Yes Alley the trtike has reverse. I never use it but I will check the cable and reverse shifter.
|
|
|
|
Post by Alleyoop on May 14, 2011 14:46:46 GMT -6
Triker98304,
You tighten the Castle Nuts so that the Hub does not move on the Axle and Make sure a Castle Nut SLOT lines up witht he HOle in the Axle so that the Cotter pin goes into the Slot of the Castle nut and the hole. That is the only thing that keeps the Castle Nut from coming loose.
Alleyoop
|
|
Certified Clinician
Currently Offline
Icebear Trike 150-9
Posts: 56
Likes: 0
Joined: May 31, 2010 20:32:41 GMT -6
|
Post by Triker98304 on May 15, 2011 17:17:01 GMT -6
Thanks Alley,
The Castle nut is now tight with a cotter key thru the axle. Will get the hose clamps today and see if I get this thing rolling down the road again...
|
|
Certified Clinician
Currently Offline
Icebear Trike 150-9
Posts: 56
Likes: 0
Joined: May 31, 2010 20:32:41 GMT -6
|
Post by Triker98304 on May 21, 2011 16:29:44 GMT -6
Finally got it on the road again.
|
|
..BAD TO THE BONE..
...
...
...
