|
|
Post by Alleyoop on Aug 4, 2012 18:17:37 GMT -6
Hi Trikers, Jordi Ramos( jotrike2011), has a trike and he has emailed me to see if any other triker has run into the following problem: He has done this because he cannot explain it to well he is from another country. His Right Axle the part that FITS INSIDE THE WORM GEAR SLEEVE has worn down smooth. So now the Axle WORM GEAR does NOT TURN THE AXLE to turn the Wheel. Now that axle has GROOVES just like you see in the picture and that groove slides into a KEY BUILT inside the WORM GEAR SLEEVE. Here is a Picture of the Rear AXLE Pay attention to the YELLOW LABEDED parts that I put wrote about. Alleyoop  |
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on Aug 4, 2012 20:58:57 GMT -6
Al, from the sound of it and the looks of how it slips into the key, there is no way it could slip in and out enouogh and if so wear would be on both parts. Sounds like the right axle was not properly harden. Replace axle and move along. Later I will post. when I remove rear gear box a picture of the shaft like the one I posted were the rear sproket from the chain has
moved the spline groves and sloted it. Just soft metal and must be replaced.
Magoo
Magoo ya done it again....Just beat it with a hammer and it fill fit in....
|
|
Senior Clinician
Currently Offline
Posts: 108
Likes: 0
Joined: Apr 26, 2012 6:16:41 GMT -6
|
Post by tierod on Aug 4, 2012 21:00:56 GMT -6
Alley it looks very simple but what would make it do that a bent axle?
|
|
|
|
Post by Alleyoop on Aug 4, 2012 21:05:12 GMT -6
I told him there is no way to fix that BUT HE needs to get a new Axle and possibley a New Worm Gears.
Tierod,
No not a bent Axle crap that is some hard metal, I think it was just a bad piece that was not hardened properly. I would guess the KEY and the Worm Sleeve would get eaten away first rather than the Hardened Axle.
Alleyoop
|
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on Aug 4, 2012 21:21:55 GMT -6
Your RIGHT ON the Money Al. I remember when I was a kid Honda cases sometimes. And getting parts...
HERE WE GO AGAIN....Magoo
|
|
|
|
Post by Alleyoop on Aug 9, 2012 14:12:32 GMT -6
|
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on Aug 9, 2012 17:56:00 GMT -6
Would like to know if he can see any wear at all on the receivers?  Looks like wrong hardness but if there is any wear inside, any at all....better replace the inner too. He can check with a pen light, hope they show no wear. But if they do he will have to remove the diff. Order the parts and go for it... Magoo |
|
Scooter Doc
Currently Offline
Posts: 316
Likes: 0
Joined: Feb 28, 2011 12:11:27 GMT -6
|
Post by justbuggin on Aug 9, 2012 19:30:10 GMT -6
jb weld it up and selftapper sould do just joking did it have proper lubication
|
|
|
|
Post by Alleyoop on Aug 11, 2012 15:43:12 GMT -6
Hey Jordi,
Have you Filled the Differential with GREASE, it may be DRY, I use FULL SYNTHETIC GREASE and put it in until it will not pump anymore.
Alleyoop
|
|
Clinician
Currently Offline
Posts: 24
Likes: 0
Joined: Mar 24, 2012 10:07:27 GMT -6
|
Post by jotrike2011 on Aug 11, 2012 16:49:17 GMT -6
Hello
to short time that he had changed the engine oil, lubricate the chain and fill the differential
Jordi
|
|
|
|
Post by Alleyoop on Aug 11, 2012 18:01:43 GMT -6
I think the axles are DEFECTIVE and were not hardened properly. If anything the Key inside the WORM GEAR SLEEVE would have broken off but not the AXLE slots.
Alleyoop
|
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on Aug 12, 2012 9:26:10 GMT -6
If that metal was harden right it would take a gringer to slot it. If the keys are not damaged at all than they just were not harden properly. Order new axles and clean the diff. out and regrease and ride the piss out of it...
Magoo
|
|
Clinician
Currently Offline
Posts: 24
Likes: 0
Joined: Mar 24, 2012 10:07:27 GMT -6
|
Post by jotrike2011 on Nov 28, 2012 16:48:44 GMT -6
Hello again
tell you that I have my trike fixed and running
I finally had to make the rear axle right here in Barcelona Spain since the Chinese dava no signs of life
By far so good and I think it is better quality than the standard
a greeting
Jordi
|
|
|
|
Post by Alleyoop on Nov 28, 2012 21:38:12 GMT -6
WOW!! Sorry to hear that you had to find someone to build you new AXLES because the Company would not respond. I am sure they wher made out of much better metal than the cheap metal they used in china. But it is not good because now if something else goes wrong for that Trike you may not be able to get parts.
Good Luck Jordi, and don't be a stranger also take pictures of your trike and put it up or send them to me and I will add them to this Thread.
Alleyoop
|
|
Clinician
Currently Offline
Posts: 1 
Likes: 0
Joined: Jul 1, 2016 10:03:41 GMT -6
|
Post by daveficker24 on Jul 1, 2016 10:41:19 GMT -6
I need to know if anyone ever found axles for trikes,mines poppin n bangin in real hard.i have 2014 icebear,it does not have 2 bolts holding axle in.C clip is out and it looks like bearing must be pressed in holding it.got it to move out 1/4 in.i just need input about anything related.i have 2 axles,1st axle was making noise from the start so they sent new warranty replacement. Thankx, Dave
|
|
..BAD TO THE BONE..
...
...
...
Looks like wrong hardness but if there is any wear inside, any at all....better replace the inner too. He can check with a pen light, hope they show no wear. But if they do he will have to remove the diff. Order the parts and go for it...
