8 pole flywheel v/s 11 pole By scatterbrained (Read 1,151 times)

[scatterbrained]

Hi I'm new to the forum and fairly new to the gy6 engine. I'm wanting to do the 11 pole stator conversion since I can't find the elusive center tap 8 pole stator to replace my original. My question is this... Will the 8 pole flywheel work with the 11pole stators? The id of said flywheel is 3.555in or 90.297mm. Thanks for any help guys!

[tvnacman]

I had checked the said 11 magnet flywheel with a sheet of paper and iron fillings then only counted 8 magnets based on the pattern of the fillings .

I also tested the 11pole stators output with a 7pin regulator , I was able to load it to 125w and keep 13.3vdc .
The answer to your question is yes . I have had one problem with selling a replacement flywheel stator and regulator . It was to a SYM owner , what we found the pick up was in a different location the engine would not run .

John

[scatterbrained]

Thanks John! I will be calling you on Tuesday to confirm the order. You have been a big help to me. I have run the new wires for the stator, 3 yellow and 1 green to where I will mount the rectifier. The wiring diag. on this forum is pretty straight foward. Damn fine diag. If I have any issues I'll definatly give you a call.

[scatterbrained]

Hey John I found a 40A relay and I have one question. The relay needs switched power to close the circuit and activate the lights. Where did you tie yours in for this switched power? I'm iffy about tying it on the same circuit as the power out of the ignition switch because it seems like it would tell the voltage sensor wire from the rectifier to charge all the time. What do you think? Thanks for your help!

[tvnacman]

The control coil of the relay we spoke about is an ac coil , energized off the white wire from the regulator .

John

[scatterbrained]

Sorry to keep on you about this John but do you have maybe a part number or specs for that relay? The reason I'm asking is because I am trying to find one that will work locally. Also if I pay for two day shipping could you do that when I order? Thank you John!

[Alleyoop]

SHOOT!! John will get on his 150 scoot and race down and deliver it in person no extra charge.
Look for this guy
Alleyoop

[tvnacman]

Here you go , www.functionaldevices.com/building-automation/display.php?model=RIBH1C

Now that I think of it I can get it local to me and ship it with your order . The last time I drop shipped from where I got it at a higher price . I can make a call and get you a price .

John

[scatterbrained]

Thanks man for all your help. I know it sounds like another sob story but I'm stuck in Knoxville tn and I'm trying to get home to Aiken sc for Christmas. I am hoping that this install will be as painless as possible. If you can get me together a total price on the relay, 7 wire regulator, 11 pole stator, and if you can get it to me in 2 or 3 days. If you can't I understand with it being so close to Christmas. You can send me a new invoice to my email. Again thank you so much for helping another 2 wheeler out.

[tvnacman]

If can get the relay in the same small flat rate box we are in good shape just the cost of the relay . I can play around to try to get all the items to fit . I may remove the parts from there boxes to get them to fit . As long as your good with that . The flat rate is about the quickest without going into the $20-30 range for shipping .

John

[scatterbrained]

Ok that sounds good to me. Just let me know. I will be ordering all this tomorrow john. Thanks man!

[scatterbrained]

Thank you sir.

[tvnacman]

I'll get the relay tomorrow .

John