Certified Clinician
Currently Offline
Posts: 85 
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 10, 2015 16:53:56 GMT -6
I'm happy with the progress they are making on the scooters..
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 10, 2015 11:37:49 GMT -6
pretty sure the mystery *bell* button was called the PANIC button by the dealer... will test it later..
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 10, 2015 8:09:08 GMT -6
i have the exact same issue... low idle rpms... will get out screwdriver this morning..
happy to report..... following directions above.. i was able to change the idle RPMs to satisfaction.. now idling at 1500 +/- tire in a very very slow rotation.. almost vibration speed... it sounds right... thanks very much!
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 10, 2015 7:51:37 GMT -6
new scooter is running strong... breaking it in slowly... now begins the search for the various parts ... i habvent been using the REMOTE.. but may try that today to master the buttons... i was given instruction on START, ENGINE STOP, SET ALARM, TURN OFF ALARM... but there is one mysterious button I'm not sure of.. i will test it later.. but if anyone knows what it is.. please advise.. its a BELL button... any ideas?
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 9, 2015 17:41:34 GMT -6
my last scooter has a left turn and lock system.. so i guess out of habit i expected the same.. I'm growing used to the straight wheel lock.. and i usually am in the seat before i unlock the wheel
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 9, 2015 7:37:03 GMT -6
needs carb adjustment... cold idle RPMs is 900.. warm RPMs is 1100... seems I've read it should be 1500.. when i rev just a bit.. to 1500RPMs.. it sounds comfortable.. but then I'm no expert
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 9, 2015 6:20:11 GMT -6
haven't inspected it closely yet.. got it at 3:30pm yesterday... the transaction went pretty quick.. quick check drive around the block.. add a bit more gas.. sign papers.. i will check things more closely tomorrow.. have a busy day ahead here... didn't notice the registration "? plate until i got home.. and found it to be a yy250t... not really a big problem.. to me it was 6 of one half dozen the other.. in f act i rather like the video of adjusting valve? on the conway over the 54B.. i will stick with it.. one glitch I've come across... the handle bar lock... doesn't lock with a full left tilt... it locks on center... hmmmm not sure if this is a feature.. or a screw up
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 8, 2015 18:55:43 GMT -6
pic sent
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 8, 2015 18:49:49 GMT -6
one very pleasant surprise was.. i can fit a half helmet under the seat... i didn't expect that.. AZ does not require helmets.. but i carry one anyway.. incase i get a passenger
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 8, 2015 18:47:07 GMT -6
yes i can email it.. what is your email address?
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 8, 2015 18:45:56 GMT -6
well the pic didn't take.. so i will have to look further to find out how to post a pic.. in mean time.. the original order was for a 54B... but what was delivered was a conway YY250T (244CC honda clone)... not sure if I'm worse off or better off... but i have noticed that adjusting valve? (or was it the gas- air mix?) is much simpler on the honda clone... at any rate.. my china doll is home.. and she ran noticeably smoother after only a few miles... what i have noticed so far is.. the fit and finish leaves a bit to be desired.. and for another $25 US... probably much less in china currency... the fit and finish quality could be improved considerably... why would they take it to th next level for a measly $25
.. thats my first impression
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 8, 2015 17:37:35 GMT -6
roketa 250cc .file:///Users/admin/Desktop/myscoot.jpeg... ok the pic didn't take.. i will send it to bashan
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 8, 2015 13:33:04 GMT -6
finally... scooter is being unloaded from the truck.. and will be set up .. and ready in 2-3 hours... can't wait.. pics to follow tomorrow if all goes well... its been a LONG wait
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 7, 2015 17:38:55 GMT -6
cyborg.. i was expecting it today.. dealer said delivery today.. earlier.. but has not responded to messages .. maybe tomorrow.. id like to be riding again
|
|
Certified Clinician
Currently Offline
Posts: 85
Likes: 4
Joined: Dec 27, 2014 9:51:56 GMT -6
|
Post by woofman on Jan 7, 2015 13:12:13 GMT -6
i will look for the kill switch.. that would work.. still waiting on dealer to let me know my scooter is set up and ready
|
|
