|
|
Post by Bashan on May 3, 2012 4:08:30 GMT -6
I'm about to tear down and rebuild on my Frankenstein scooter's GY6 engine for a forum project. I thought I'd make it a group effort on this board but before I start I wanted to make a test bench. Here's a Youtube with some further pictures afterward:
Rear bracket:
Gas tank, B&S fuel valve (Sprocket approved!), and lawn mower filter:
CDI with busbar:
Battery and coil:
Exhaust strap:
You can just see the red CDI AC power wire peeking out behind the flywheel. I took the center tap off of the yellow wire on this stator which floats the ground. This allows you to use the resulting two equal AC stator wires as yellows for a Trail Tech rectifier (see thread):
|
|
Doc's Anything Goes
Currently Offline
Posts: 2,739
Likes: 66
Joined: Oct 23, 2010 19:29:21 GMT -6
|
Post by tvnacman on May 3, 2012 8:25:51 GMT -6
Very nice Rich!!!!!!!
Can I interest you in an 11pole stator, magneto and 7pin regulator for testing
? I also should be getting some ballast resistors.
John
|
|
Scooter Doc
Currently Offline
Posts: 1,319
Likes: 5
Joined: Feb 17, 2011 19:36:47 GMT -6
|
Post by mike6736 on May 3, 2012 9:33:27 GMT -6
Nice Rich... Sure would like to get my Magnum 300 to idle like that, I think it would tear that thing all up. Always liked the 150cc
Mike
|
|
Scooter Doc
Currently Offline
Posts: 1,936
Likes: 7
Joined: Jun 18, 2010 22:25:14 GMT -6
|
Post by sprocket on May 3, 2012 18:16:38 GMT -6
You know that is how the work on engines in China etc.. they would never work on an engine in the bike they simply 'pop' it and put it on the bench.. just like you have...
Saves the back and is SO much easier to work on...
Good job..Rich
|
|
Scooter Doc
Currently Offline
Vespa Specialist
Posts: 426
Likes: 6
Joined: Feb 26, 2011 20:14:53 GMT -6
|
Post by Kaveman on May 3, 2012 18:21:58 GMT -6
Nice Rich ! Top Kudos from me !
Will
|
|
Doc's Anything Goes
Currently Offline
Say no to scooter abuse
Posts: 3,873
Likes: 156
Joined: Mar 31, 2010 19:07:16 GMT -6
|
Post by jct842 on May 3, 2012 22:19:43 GMT -6
:)now.....it would even be nicer if you could put a load on the motor!  john maybe chain drive to the tiny little wheels on the cart? I have thought about doing some thing just like that....and you did it! |
|
|
|
Post by Alleyoop on May 3, 2012 23:15:44 GMT -6
Very nice, that is what every shop should have a TEST BENCH.
Alleyoop
|
|
Clinician
Currently Offline
Posts: 1
Likes: 0
Joined: Dec 29, 2020 23:04:36 GMT -6
|
Post by jpkboudreau on Dec 29, 2020 23:09:32 GMT -6
Rich,
Thanks for posting this information. I am trying to make a wiring harness for a gy6. Could you indicate/identify where the wires go on the engine. You have good pictures of you bench wiring but I need help figuring out where the wires terminate or tie into on the engine itself.
Thanks!
Pascal
|
|
Clinician
Currently Offline
Posts: 8
Likes: 0
Joined: Mar 30, 2021 5:12:56 GMT -6
|
Post by maria26886 on Mar 30, 2021 5:15:56 GMT -6
|
|
...
...
...
john
..BAD TO THE BONE..
