Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 17, 2012 4:06:07 GMT -6
I got a gy6 and the starter works fine unrolled I put the case cover back on   ?? It's for my stepson and we have been working it together and he is bumed out over it!!! Don't know what would cause this? I'm good with all motors and I'm stupefied??? I know someone up here can help or give me some ideas!! Anything would be awesome and will be very apreciated!!!!!! Thanks for help and looking!! |
|
|
|
Post by Bashan on Jul 17, 2012 14:24:01 GMT -6
Is it a 50cc or what? You mean you put the CVT cover on and it won't turn over? Rich
|
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 17, 2012 20:06:22 GMT -6
It's a 150 and it turns over it just drags real slow but works fine without the cover but drags real slow after a full revalotion? I don't get it!!!
|
|
Scooter Doc
Currently Offline
Posts: 1,936
Likes: 7
Joined: Jun 18, 2010 22:25:14 GMT -6
|
Post by sprocket on Jul 17, 2012 20:43:43 GMT -6
Gee.. that's a new one..I wonder if thereis an interlock switch on the CT cover..some scooters had those..what year?
Long shot ...run a 16 AWG wire from the engine block to the bare frame and try it..it might be a grounding problem
|
|
Scooter Doc
Currently Offline
Posts: 316
Likes: 0
Joined: Feb 28, 2011 12:11:27 GMT -6
|
Post by justbuggin on Jul 17, 2012 22:17:09 GMT -6
check and see if there is any binding with the way the motor is bolted in and use a heavy gage wire 16 awg is not heavy enough use like an 8 awg wire for a ground the wire size is the smaller number the bigger wire cross section
|
|
|
|
Post by Bashan on Jul 18, 2012 9:43:51 GMT -6
Wow, that IS a new one. OK, your starter is outside the CVT cover and on top of the engine on the left side......is that correct? Maybe the kickstart mechanism is getting pushed against something when you put the CVT cover on. I'm just floating balloons here, I'm mystified. Rich
|
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 18, 2012 9:48:29 GMT -6
I've got an 8 awg for the ground wire!!! And like I said it works fine with the cover off just when you put it pack on it starts! I greesed the reduction gear and the sleve that goes in it I'm at a loss too!!!!
|
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 18, 2012 10:32:36 GMT -6
Yes the starter is on the outside to the cvt cover to the left and the kick start disengaged seem to be pressing on anything that was the first thing I cheaked out! I have no clue either that's why I'm here!!! Hope someone has a clue but thank all of you for your time and help!!! Really!!!!
|
|
Scooter Doc
Currently Offline
Posts: 316
Likes: 0
Joined: Feb 28, 2011 12:11:27 GMT -6
|
Post by justbuggin on Jul 18, 2012 11:06:05 GMT -6
is the motor hard to turn over pull the plug out and try turning the motor by hand it should be easy with out the plug in
|
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 18, 2012 12:24:32 GMT -6
Yes it still drags a lil without the plug in but not as bad!!! The starter is putting out the right voltage and I grounded it to the frame now so I'm really at a loss???
|
|
Scooter Doc
Currently Offline
Posts: 1,936
Likes: 7
Joined: Jun 18, 2010 22:25:14 GMT -6
|
Post by sprocket on Jul 18, 2012 12:36:25 GMT -6
Are you certain there is no interlock switch on the CVT cover? There is no way the CTV cover could interfer with the starter unless it is physically putting a load on the engine by rubbing or restricting something...
|
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 18, 2012 13:07:34 GMT -6
That's what I'm saying? Thought someone would have an idea?? What would an inerlock switch look like? I'm learning about these things as I go? ? So any insure is great!!! |
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 18, 2012 13:08:10 GMT -6
That's what I'm saying? Thought someone would have an idea?? What would an inerlock switch look like? I'm learning about these things as I go? ? So any insure is great!!! |
|
|
|
Post by Alleyoop on Jul 18, 2012 13:30:30 GMT -6
Does your CVT look like this? If so the shaft end on the BENDIX FITS INTO A HOLE ON THE INSIDE OF THE CVT ITSELF to align it so it is straight and supports the bendix. If the end of the shaft is NOT supported and in the hole it could be hanging up the Variator from turning and or causeing to bind the gear on the starter. Alleyoop  |
|
Clinician
Currently Offline
Posts: 10
Likes: 0
Joined: Jul 17, 2012 3:50:36 GMT -6
|
Post by spnov on Jul 18, 2012 14:10:29 GMT -6
Mine is simaler but my drive belt isn't on the same side of the motor!! Someone told me its a Chinese motor but a motor is a motor and usualy I can make anything run but this starter is driving me nuts!! It is in the hole for the cover or it wouldn't go on! It has to fit! Or it won't fit! You know what I mean!! I'm just going to keep testing and trying I don't know what else to do! I'm not the type to just quite!! Know what I mean!! Thanks for your time and ideas if you have anymore let me know please? ?? |
|
?? It's for my stepson and we have been working it together and he is bumed out over it!!! Don't know what would cause this? I'm good with all motors and I'm stupefied??? I know someone up here can help or give me some ideas!! Anything would be awesome and will be very apreciated!!!!!! Thanks for help and looking!!
..BAD TO THE BONE..