|
|
Post by crwford on Aug 31, 2017 9:51:50 GMT -6
are you running it with out a exhaust pipe and muffler?
|
|
|
|
Post by crwford on Aug 31, 2017 9:48:57 GMT -6
remember can't check compression with finger. With a gauge it may take four or five cranks before you get a a create reading. try spraying some starter fluid in carb likely see what happens check gap on valves check flow of fuel from gas tank and open gas cap try with out cap on a few things to try first.
|
|
|
|
Post by crwford on Aug 27, 2017 11:12:05 GMT -6
maybe reed valves not closing completely?
|
|
|
|
Post by crwford on Aug 27, 2017 9:15:03 GMT -6
did you check the vacuum line going to valve right hand side of carb for being anti back fire?
|
|
|
|
Post by crwford on Aug 16, 2017 17:54:49 GMT -6
why now rapid Jim he is a Ice Bear dealer I get mt Zodiac parts from him all the time. He listed as Rapid Repair listed above.
|
|
|
|
Post by crwford on Aug 9, 2017 20:32:41 GMT -6
Before I do that I would be looking for a vacuum leak causing it to run lean, and by you adding a little choke you are riching it back to normal.
|
|
|
|
Post by crwford on Aug 1, 2017 12:32:45 GMT -6
Jim is the man for sure I been doing business with him for a few years you can count on him even if you have a problem. He is a dealer and service person if he can't answer your question he will call Ice Bear and fine one for you.
|
|
|
|
Post by crwford on Jul 31, 2017 20:51:41 GMT -6
If you let it sit a while use stable gas treatment it will save you from you having to do this. They also have treatment if you have methanol in your gas you should use is regular. We have 3 Ice Bear trike's 300cc Zodiacs great bikes for the money.
|
|
|
|
Post by crwford on Jul 31, 2017 20:44:48 GMT -6
It it sat a while carburetor will need to be clean good and be fine after that
|
|
|
|
Post by crwford on Jul 19, 2017 9:31:43 GMT -6
try getting a flexible magnet and open drain plug slide it around till it latches good luck.
|
|
|
|
Post by crwford on Jul 17, 2017 19:13:41 GMT -6
On the Ice Bear trike check the rubber intake make sure its clamps is tight and no cracks in it first before tearing hair out of you head.
|
|
|
|
Post by crwford on Jul 16, 2017 13:49:58 GMT -6
time for new parts for sure as long as you are in there replace the rollers with right grams of weight. and get out riding LOL
|
|
|
|
Post by crwford on Jul 11, 2017 16:31:47 GMT -6
70 if my ball let me and tractors don't try blowing me off the byway don't like it won't do it any more country roads 55 is good enough LOL and had no wind LOL
|
|
|
|
Post by crwford on Jul 8, 2017 12:06:59 GMT -6
My 300cc trike 60 mpg but I'm a little heavy 235 and so is my wrist crusting speed 45 to 55 most of time.
|
|
|
|
Post by crwford on Jul 8, 2017 12:02:04 GMT -6
I been using it for 2 years in my 3 Zodiac's by Ice bear the water less stuff if great in parades while many others over heating we are still going with no temperature change. But remember it costs and you need to use it's pre wash it get out all water in system but in long run it pays you back because it's life time no need to change it out. As far as your shrouds I can't say mine have none. Evens is the best as far as I'm concerned. Heck if Jay Leno would put it in his big buck cars it's good for me also LOL
|
|
