Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 20, 2011 21:30:02 GMT -6
oh, lol thanks, I didnt realize that. I'll get them off the ebay. is there a how to to get the instrument panel off or is it the 4 screws i see.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 20, 2011 21:11:28 GMT -6
so after all my repairs I notice the front wheel makes a roaring sound, so I thought bearing, but if I suspens the front tire and spin it there is no noise,. maybe the kendra original knobby tire? also seems to wobble at the front too. tire with lump?
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 20, 2011 20:56:39 GMT -6
thanks I should be more clear, its the red ring around it, the back lighting works for bothe gauges, but the red ring is gone on the speedo. how much of a pain would it be to replace anyway.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 20, 2011 20:30:06 GMT -6
Does anyone know where to find the bulb for the gauges on a roketa mc-54-250b, the speedo light is burned out.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 15, 2011 20:51:36 GMT -6
i rented an impact i kinda thought i was about to bend shocks wheel ect. everything is back thogether and fine except the rollers although good there are 8 not 6 so when i bought some and went to put the in I found I was short 2. thankfully the ones i had were good. valves adjustedx, still rattles in final drive box but the wheel bearing feels tight. next i have to figure out why it bogs even after a valve job.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 15, 2011 6:49:14 GMT -6
can i stick a pipe through the whell and let the shock hold the wheel too?
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 14, 2011 18:20:59 GMT -6
how do i remove clutch without an impact wrench?
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 14, 2011 10:02:04 GMT -6
I've noticed a rattling sound from the variator, so I assume the rollers are bad. but the clutch seems to have a knocking sound, unless its being caused by the variator.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 14, 2011 7:56:16 GMT -6
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 14, 2011 6:46:38 GMT -6
thanks I'll give it a go.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 14, 2011 6:39:44 GMT -6
cruiser did you mean remove the belt? so if the noise is still there its the variator? Thanks alley pop i'll take it apart and check the spring.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 13, 2011 21:08:07 GMT -6
good idea, noticed tonight that that variator has a rattling sound. guess it needs bearings as well. how do i post pics?
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 13, 2011 19:03:36 GMT -6
maybe bad fuel, drain tank and carb bowl and hope you dont have to rebuild carb.
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 13, 2011 18:34:56 GMT -6
Does anyone have good advice as to where to find the parts?
|
|
Certified Clinician
Currently Offline
Posts: 72
Likes: 0
Joined: Jul 8, 2011 8:04:14 GMT -6
|
Post by deanc on Jul 13, 2011 18:07:27 GMT -6
thanks i'll try that. also the bell looks purpled and if its off the belt is half way down in the pulley. how would I fix this if the parts look good, re grease them or replace the pulley bearings, or clutch?
|
|
