Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 28, 2011 15:32:43 GMT -6
my scooter runs good but looking for more performance mods are number 88 main jet all parts are performance iam listing air filter exhaust 5g sliders new DC CDI BOX all scrappy parts hot coil new tiatum plug pvc vent that sumes it up i bought yellow 1500 main spring and yellow clutch springs also bought 6g and 7g sliders have not put yellow springs in or 6g/7g sliders not in yet eaither what can i do to get my belt to ride higher to get more top end i have alot of parts to work with my factory speedo reads 55mph but thinking its wrong please help with more speed at take off and top end tx eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 26, 2011 18:15:23 GMT -6
what is the reason people change them up hill only really what weights should i use i have 5g in now
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 26, 2011 11:56:53 GMT -6
how do i get my belt to ride high upon the pulley buy changing main big spring to a yellow 1500 rpm one or how else do i get belt to ride high as i can eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 25, 2011 18:09:17 GMT -6
hey allyoop should i add a 1500 rev yellow conture main clutch spring so my belt rides up higher i did buy one from scrappy will the stiffer spring let my clutch ride higher up correct i just did not puy iy on yet let me know asap k eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 25, 2011 13:07:38 GMT -6
back the ebay item number is 350367765020 buy it or shipp it back help please eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 25, 2011 13:03:33 GMT -6
so to some it up the one i bought from scrappy performance DC CDI and the new racing one DC CDI with 4 degrees of advance spark and no revelimit neither one will me will help me or yes the racing one will still confused should i refuse shippment or try it out take a look at the one on ebay item number brb eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 24, 2011 18:53:52 GMT -6
I BOUGHT A PERFORMANCE DC CDI BOX FROM SCRAPPY WORKED OK BUT NOW I BOUGHT A DC CDI RACING BOX ON EBAY WILL I NOTICE A DIFFERANCE OR DID I WASTE MY MONEY THE NEW ONE SAYS INCREASE SPARK ADVANCE 4 DEGREES AND 8 TO 10 PERCENT MORE POWER DID I DO THE RIGHT THING PLEASE TELL ME ASAP SO I HAVE TIME TO RETURN IT ERIC help asap thanks
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 20, 2011 18:54:00 GMT -6
if you read my mods can i go with a number 95 main jet and a 88 idle jet for hard starting will this work ok and not flood my motor please help asap iam tring this tomrrow please help run good but a little hard to start eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 19, 2011 19:19:01 GMT -6
thank god thats great news for once better than any scooter news amen
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 19, 2011 14:32:57 GMT -6
cork and heating tip to keep cork from sliding off heat tip to red hot needle nose plyers bent upward keeps the cork from sliding off problems fixed thanks everyone this site rocks ERIC
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Fuel gauge
by: Tawas - Sept 19, 2011 14:29:03 GMT -6
Post by Tawas on Sept 19, 2011 14:29:03 GMT -6
i had a similar problem replace float with a cork it works slide cork on heat up wire tip bend it upward and it fixed all my gas gauge problems you have to heat up tip to keep cork from sliding out wire is very stiff but a propane torch gets it red hot and bends easy to keep it from sliding off ERIC GOOD LUCK
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 18, 2011 17:02:34 GMT -6
did some mods all performance new DC CDI new 5G SLIDERS new titanum plug new number 88 jet new air filter new scrappy chrome exhaust i get 55mph on factory speedo if i move up to a number 95 jet will i get even more top and bottom end runs good but i bought a number 95 in case 88 did not work can i go to 95 helping it or will it flood the engine if i get more speed by changing it i will if not i dont want to have to go back to 88 any for sure answers i dont care about mileage at all please help eric in tawas mi
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 18, 2011 16:49:49 GMT -6
thank you guys i tried a cork and got it working but will the gas eat away at the cork and melt in my gas causing bad gas to run thru my motor or it will not affect the cork at all thank you so much for the tips eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 18, 2011 11:47:01 GMT -6
the gas gauge and float all work the way it should when i take the float out and move up and down everything works the dial and float all work right but when i install it its just goes down to empty and stays there so all electrical float and gauge works like i said when installed shoots to empty and sits there MAD AGAIN lol eric
|
|
Senior Clinician
Currently Offline
East Tawas MI
Posts: 119
Likes: 0
Joined: Sept 11, 2011 14:47:52 GMT -6
|
Post by Tawas on Sept 17, 2011 19:33:42 GMT -6
i have a 2009 lifan 50cc gy6 motor my gas gauge never worked i unscrewed the gauge out and my float doesnt appear to be leaking i oiled the top moving part and moves freely everything seems working as i move it back and forth is there a easy fix maybe bending wire straight instead of the bend i read the post on how to fix it but still cant get it to work right any more ideas eric 586-292-2979 will it work if i bend wire stright to get it to work thought of a cork i dont know its really making me MAD lol HELP PLEASE
|
|
